Introduction of pallet tilter
LT series lift and tilt pallet jack are designed to lift the pallet and tilt it to the ergonomic angle. LT10M manual pallet tilter & LT10E electric pallet tilter are worked to allow the users to ergonomically reach loads easily without having to bend down or over-stretch. The Electric tilt pallet jack has forced steering on one wheel to make manoeuvring easy. Lift /lower functions are controlled by a switch on the control lever. Tilt/return functions are controlled by a remote control, which is fitted with a long wire, and can make the operator and the tilter with load keep a certain distance, more safer. Lift /lower function and Tilt/return functions can be operated independently of each other or simultaneously. When Tilt/return functions are to be used, the tilter must be on a firm surface, and the universal wheel shall be braked. When Tilt/return functions are to be used to stack materials, the handle can be turned to the side to make access to the stack table easier.
As a pallet tilting equipment, this pallet jack tilter can be used as a pallet truck and also a tilting pallet truck, this can not only improve your work efficiency, but also save costs.
手柄可以旋轉並鎖定在遠離工作區域的位置。它適用於坐姿和站立姿勢。托盤傾斜千斤頂的前叉最多可傾斜90度。它們都標配了駐車製動器和腳保護器。
符合EN1757-1和EN1175
Details of pallet tilter
LT0M manual pallet tilter LT10E electric pallet tilter
We have this item in stock in France/US, if you are located in Europe or US, we can arrange delivery to you ASAP! This way will save your time and shipping cost.
Specifications of pallet tilter
| 我電梯號 | 1520902 | 1520903 | |
| 模型 | LT10M | LT10E | |
| 類型 | 手冊 | 電動 | |
| 容量 | 公斤（磅） | 1000(2200) | |
| 提升高度，垂直 | h毫米（英寸） | 285(11.2) | |
| 最小貨叉高度 | h1毫米（英寸） | 85(3.3) | |
| 貨叉長度 | 我毫米（英寸） | 800(31.5) | |
| 手柄高度 | L1毫米（英寸） | 1138(44.8) | |
| 貨叉總寬度 | b毫米（英寸） | 560(22) | |
| 貨叉之間的寬度 | b1毫米（英寸） | 234(9.2) | |
| 滾筒前叉尖長度 | L2毫米（英寸） | 135(5.3) | |
| 整體的寬度 | B毫米（英寸） | 638(25.1) | |
| 總長度 | L毫米（英寸） | 1325(52.2) | 1410(55.5) |
| 整體高度，升高 | 高mm（in。） | 950(37.4) | |
| 整體高度，降低 | 高mm（in。） | 750(29.5) | |
| 負載中心最小/最大 | C1毫米（英寸） | 200/400(8/16) | |
| 負載中心最小/最大 | C2毫米（英寸） | 200/420(8/16.5) | |
| 動力單元 | 功率/功率 | -- | 0.8/12 |
| 淨重 | 公斤（磅） | 178(391.6) | 185(407) |
安全守則
1. Driving the pallet tilter on the slope
1) The pallet tilter shall be unloaded or a small load.
2）負載應位於最低位置。
3) The gradient shall be no more than 2° when dragging the pallet tilter.
4）無論是升級還是降級，操作員均應處於較高位置。
2. Avoid offset loads
負載必須均勻分佈在貨叉或貨盤上，重心與貨叉前部之間的距離為400mm，最大重心高度為420mm，最小為200mm，超出此範圍的距離將降低安全，增加風險。
托盤或貨叉上的貨物必須妥善固定，避免負載不平衡，以免在運輸過程中，叉車抬升或叉車必須保持抬高一段時間的情況下掉落。
3. Driving loaded
The tilting pallet jack is designed for use on even and level floor. During transport the forks shall be raised as little as possible. Transport with raised forks should be made over the shortest possible distances and at low speed. Do not transport when tilting goods on the pallet tilter, this is not safe.
警告： 切勿將手或腳放在活動部件上，否則有受傷危險。
